Assessment of pressure swing adsorption as CO2 capture technology in coal-fired power plants
MetadataVis full innførsel
Coal-based power generation is responsible for a significant share of CO2 emissions on a global scale. Technologies to drastically reduce coal carbon footprint are critical for meeting mitigation targets. Absorption, whether chemical or physical depending on the process framework, is commonly regarded as the most mature technology in this context. Nevertheless, absorption suffers from some drawbacks, such as high energy requirements and corrosion of process equipment. Adsorption is considered as a promising alternative, with potential for reducing energy penalty, environmental impact and cost of CO2 capture. The main objective of this thesis is to assess the viability of a process relying on adsorption, i.e. pressure swing adsorption (PSA), as CO2 capture technology in coalfired power plants. In order to get a comprehensive overview on the prospects of PSA, different cases were considered. Post-combustion CO2 capture was studied by integrating a PSA unit into an advanced supercritical pulverized coal (ASC) plant. Pre-combustion CO2 capture was studied by integrating a PSA unit into an integrated gasification combined cycle (IGCC) plant. Proper designs for these process frameworks were defined, taking into account characteristics, requirements and constraints of the systems. PSA is a discontinuous process, made of different steps undergone by each column of a PSA train. A dynamic model was built, based on material, energy and momentum balances. The developed dynamic model was then linked to the steady-state model of the power plant, by exploiting appropriate process scheduling and the cyclic steady state (CSS) condition of the PSA process (a condition in which the process transient behavior becomes steady throughout different cycles). The resulting composite model allowed performing simulations and analyses on a system level. The post-combustion case (ASC + PSA) showed competitive energy performance. The net electric efficiency obtained was 34.8%, whereas the reference plant without CO2 capture had 45.1%. The CO2 capture requirement was also fulfilled with more than 90% CO2 sequestrated. A comparison with chemical absorption - performing with 34.2% net electric efficiency - confirmed the competitiveness of PSA. A serious issue ascertained concerned the required footprint of the PSA unit. A first estimation suggested the necessity of more than 260 adsorption columns for processing the entire flue gas coming from the boiler. The feasibility of PSA in the post-combustion case appeared less attractive because of the number of vessels needed. The pre-combustion case (IGCC + PSA) returned good results for all the performance indicators investigated. A comparison with physical absorption showed that PSA is slightly outperformed in terms of energy efficiency (36.2% versus 37.1%, with the reference plant without CO2 capture having 47.3%), CO2 recovery (86.1% versus 90.6%) and footprint. However, the performance gap was evaluated to be rather small, thus additional investigations were carried out in this process framework. Improvements in the performance of the pre-combustion case were sought by considering two domains, the process and the adsorbent material. Several possible process configurations were analysed and a range of results obtained. Improved energy performance could be obtained but to the detriment of the CO2 separation performance and vice versa. Modifications in the adsorbent material properties (attempting to simulate different adsorbents and/or advancements in the materials) showed a significant influence not only on the gas separation process but on the whole plant performance. The utilization of improved adsorbents demonstrated the capability to give a substantial contribution to close the gap with absorption, though it may not be sufficient. None of the cases studied succeeded to fully match absorption-based performance both in terms of energy and CO2 capture efficiency. Further, an approach to exploit possible synergies between the two studied domains and realize the full potential of PSA in this framework was outlined. It consisted of tuning the material properties according to a specific process configuration. The results achieved were encouraging as net electric efficiencies up to 37.1% were obtained without drastic decrease in the CO2 capture efficiency. The knowledge developed in the pre-combustion process framework suggested a further case which was believed interesting for PSA. An IGCC plant was defined coproducing power and ultrapure H2 with CO2 capture. The system is of interest both because it allows capturing CO2 and because differentiating the plant products can be advantageous in terms of flexible operation. Two novel process configurations were developed, entirely relying on PSA. The first consists of two consecutive PSA stages (Two-train PSA), while the second configuration carries out both CO2 separation and H2 purification within a single PSA stage (One-train PSA). Both these configurations succeeded to provide a varying power-to-hydrogen output ratio - the net power output could be reduced from 346 MW to 300 MW by increasing the ultrapure H2 throughput - with a constant coal feed to the gasifier and retaining plant efficiency on a good level. The common process design for an IGCC coproduction layout encompasses absorption for CO2 capture and PSA for H2 production. With regard to that, a comparative analysis seems to confirm the expected advantages brought by the utilization of PSA as the only gas separation technology. A higher integration level could be achieved, allowing significant energy savings. The assessment of PSA in this framework was concluded to be promising and worth further analyses. Summing up, it was demonstrated that PSA can be successfully integrated in coal-fired power plants as CO2 capture technology. However, the analyses carried out showed also that PSA is generally outperformed by absorption in an overall evaluation taking into account different performance indicators. Potentials and limits of the technology have been highlighted and recommendations for optimizing the performance have been outlined. The knowledge developed can be useful to address further work on PSA technology, especially in those specific frameworks (e.g. coproduction of power and H2) where PSA can reach competitiveness.
Består avPaper 1: Riboldi, Luca; Bolland, Olav. Evaluating Pressure Swing Adsorption as a CO2 separation technique in coal-fired power plants. International Journal of Greenhouse Gas Control 2015 ;Volum 39. s. 1-16 http://dx.doi.org/10.1016/j.ijggc.2015.02.001
Paper 2: Riboldi, Luca; Bolland, Olav. Comprehensive analysis on the performance of an IGCC plant with a PSA process integrated for CO2 capture. International Journal of Greenhouse Gas Control 2015 ;Volum 43. s. 57-69 http://dx.doi.org/10.1016/j.ijggc.2015.10.006
Paper 3: Riboldi, Luca; Bolland, Olav. Pressure swing adsorption for coproduction of power and ultrapure H2 in an IGCC plant with CO2 capture. International journal of hydrogen energy 2016 ;Volum 41.(25) s. 10646-10660 http://dx.doi.org/10.1016/j.ijhydene.2016.04.089